Rigger and Signaler Qualification (CITF) (SE)

Training Information

This 40-hour hands-on course covers construction rigging hardware, procedures, and load calculations in compliance with OSHA and state regulations. Included in the Rigging Qualification is the Written Test and the Practical Test that is usually held off-site. NOTICE: The Rigging Qualification NO longer has a ONE YEAR grace period.  If you need to renew your qualification, you MUST take the Rigging Refresher prior to your expiration date. Please check your TVC card for your expiration date, use the Certified Rigger and Signaler date as reference.

▲ APPRENTICES - You must have successfully complted C301 Intro to Rigging class prior to taking this course.  

*WHAT TO BRING to class: Please bring your RIGGING BOOK to class, along with a calculator, notebook, and a pencil.

 

PRACTICAL TEST Date/Time/Location:

Date: Tuesday, July 26, 2022

Times: 7:00-3:30pm

Location: 1441 Chestnut Ave. Hillside, NJ 07205 (Bay Crane)

Important Information:
PARKING - Please make sure you park your vehicle in the parking areas on the left side of the building. Personal vehicles are not allowed past the Green Dumpsters. You must walk to the back where the Crane will be set up. Only the Instructors vehicle is allowed near the Crane to facilitate their equipment.
PPE – Proper Personal Protective Equipment is required while on premise

Training Dates

Tue, 07/12/2022 5:00 pm - 9:00 pm
Thu, 07/14/2022 5:00 pm - 9:00 pm
Sat, 07/16/2022 7:00 am - 3:30 pm
Tue, 07/19/2022 5:00 pm - 9:00 pm
Thu, 07/21/2022 5:00 pm - 9:00 pm
Sat, 07/23/2022 7:00 am - 3:30 pm
Tue, 07/26/2022 7:00 am - 3:30 pm

Training Registration

You must be logged in to register for trainings

Signup Status

Remaining Openings (including wait-listed): 5
Capacity: 3/6
Wait-listed: 0/2

Contact Information

Members interested in attending this course must register by logging in and registering through the website.

Edison Training Center

Contact Information:

NCATF Edison Training Center
75 Fieldcrest Ave
Edison, NJ 08837

PHONE: (732) 372-6020

Hammonton Training Center

Contact Information:

NCATF Hammonton Training Center
3300 White Horse Pike,
Hammonton, NJ 08037

PHONE: (609) 567-5675

FAX: (609)-567-5724

Equipment Required

Members attending training must provide their own safety shoes, safety goggles, gloves, ear protection and hard hats. Failure to provide your own safety equipment may result in your being dropped from a particular training session.

Attendance Requirements

100% attendance is required for all courses that issue Certificates or Qualifications. Members must attend all class dates to receive Certification/Qualification. We ask that all members arrive on time. Late arrivals (and early departures) are disruptive to instructors and participants. Poor attendance / disruptive behavior will result in your being dropped from a particular training session.

Cancellation Policy

To maximize the effectiveness of our training sessions, we limit the number of attendees. If you are registered for a specific training and need to cancel, please take a minute and log-on to the website and withdraw from the class. Once you log-in, classes you are registered for will appear under your profile, click on the class to unregister

Failure to withdraw or notify us within 3 days of the start date of the class will result in a NO SHOW in your training history and may result in you being denied registration for future training. We reserve the right to cancel any course for which there is an insufficient number of registered attendees. Registrants may then enroll in the next available offering of the course, or cancel the registration.

Location Information

NCATF Edison Training Center
75 Fieldcrest Ave
Edison, NJ 08837